NMRV Worm Gearbox Guide: Sizes 030–150, Dimensions and Interchange
The NMRV series is the world’s most widely produced aluminum-housed worm gearbox family. Its three-digit frame numbers — 030 through 150 — encode the worm gear pair’s center distance in millimeters, and because dozens of manufacturers build to the same de facto dimensional convention, sizes, flanges, and output shafts are closely — but not always exactly — matched across brands. This guide decodes the naming system, collects dimension and torque magnitudes for every standard frame, lists the five checks that decide whether another brand’s unit will drop into your footprint, and shows where a custom worm gear set beats a catalog unit.
This reference is written for three readers at once: the OEM design engineer specifying a right-angle drive around NMRV dimensions, the maintenance engineer replacing a failed unit and wondering which brands will fit the bolt holes, and the procurement specialist comparing quoters on seemingly identical gearboxes.
One positioning note before the numbers. NMRV is not a single manufacturer’s product — it began as an Italian aluminum-housed worm reducer design and is now produced by dozens of makers worldwide, which is exactly why the dimension-and-interchange question matters. We at WormGear Mfg do not stock catalog NMRV units; we manufacture custom worm gear sets and custom equivalents to your drawing, which makes this guide our working knowledge of the standard the market measures against. For worm reducer engineering in general — ratio and efficiency bands, backlash classes, and the maximum input speed limit — see the companion worm gear speed reducer reference.
For the practical side of swapping a unit in the field — measuring an unlabeled gearbox, oil equivalents, and re-commissioning steps — read the worm gear replacement guide.
1. NMRV Naming and Frame Number System
An NMRV gearbox is a single-stage right-angle worm gear reducer: a ground steel worm on the input shaft meshes with a bronze worm wheel on the output shaft, inside a ribbed aluminum housing that doubles as a heat sink. Units are universally mounted (any shaft orientation), pre-filled with synthetic oil, and sized by a three-digit frame number.
The frame number is the worm gear pair’s center distance in millimeters. NMRV 063 means the worm axis and the wheel axis sit 63 mm apart; NMRV 150 means 150 mm apart. That single convention decodes the whole series — and it also tells you what a custom worm gear set for that envelope must be designed around, because center distance is the fundamental sizing parameter of any worm gear pair, before module, ratio, or materials are chosen.
Around the core nine frames, conventions are stable but not perfectly uniform. Most makers add nothing to the standard range; a few extend it downward with an 025 frame or insert an intermediate 105. Motovario — the brand most identified with the series — builds its higher-capacity NMRVpower variants in the 063–110 footprints. In many makers’ catalogs the sibling designation NRV denotes the same housing family without the IEC motor input flange (shaft-input only), and PC + NMRV combinations add a helical pre-stage for higher overall ratios.
If you are ordering the complete housed unit rather than the gear pair, the worm gearbox page covers the NMRV 030–150 units by model — mounting positions, IEC and NEMA input flanges, and quoting by frame number.
Construction follows a shared recipe that Motovario’s catalog states plainly and most competitors mirror: die-cast aluminum housings up to frame 110 and grey cast iron from 130 up; a worm wheel in bronze (CuSn12Ni2-class, per UNI 7013-10); a ground ZI-profile worm (UNI 4760); and load capacity computed to ISO 14521 / DIN 3996 / AGMA 6034-class standards. When two brands’ catalogs disagree, it is usually in the fine print of that recipe — lubrication, sealing, or bearing quality — not in the mounting interface.
2. NMRV Dimension Reference Table (Sizes 030–150)
The table below is the quick reference for the nine standard frames. Center distance is exact by definition of the frame number; the remaining columns are catalog conventions that vary by manufacturer and should be read as typical catalog values, not ratings.
| Frame | Center distance | Common ratios* | Rated input speed* | Output torque (magnitude)* |
|---|---|---|---|---|
| NMRV 030 | 30 mm | 5:1-100:1* | ≈1,500 rpm* | ≈13-19 N·m |
| NMRV 040 | 40 mm | 5:1-100:1* | ≈1,500 rpm* | ≈30-35 N·m class |
| NMRV 050 | 50 mm | 5:1-100:1* | ≈1,500 rpm* | ≈50-65 N·m class |
| NMRV 063 | 63 mm | 5:1-100:1* | ≈1,500 rpm* | ≈100 N·m class |
| NMRV 075 | 75 mm | 5:1-100:1* | ≈1,500 rpm* | Low hundreds of N·m |
| NMRV 090 | 90 mm | 5:1-100:1* | ≈1,500 rpm* | A few hundred N·m |
| NMRV 110 | 110 mm | 5:1-100:1* | ≈1,500 rpm* | Several hundred N·m |
| NMRV 130 | 130 mm | 5:1-100:1* | ≈1,500 rpm* | Several hundred N·m (upper end) |
| NMRV 150 | 150 mm | 5:1-100:1* | ≈1,500 rpm* | Up to ≈1,500 N·m |
*Series-wide conventions. Standard ratio steps across the series run 5, 7.5, 10, 15, 20, 25, 30, 40, 50, 60, 80, and 100 — exact availability varies by frame and maker, and small frames often omit 5:1. Input speed is the customary rating point for 4-pole motors (some makers rate slightly lower or higher). Torque figures are order-of-magnitude guides at ~1,500 rpm input, not promises — actual output torque depends on ratio, duty, and the individual manufacturer. Always size from the specific maker’s selection chart.
To anchor the torque magnitudes with published catalog points: one US-distributor chart lists the NMRV030 at 115–168 in·lb (≈13–19 N·m); distributor data for the 040 and 050 shows roughly 34 N·m and 62 N·m respectively at 1,500 rpm input and a 5:1 ratio; and Motovario’s own NMRV catalog caps the series at 1,550 N·m output torque, 18.5 kW input power, and admissible radial loads up to 18,000 N on the output shaft. Between those anchors, treat each frame’s tier as a shortlisting guide and confirm with the maker’s chart.
A note on the ratio column: because the frame number fixes only the center distance, two NMRV 063 units at different ratios share a housing footprint but differ in torque, efficiency, and self-locking behavior — a single-start high-ratio set runs cooler in ratio but less efficient per mesh, exactly as worm gear physics dictates. The frame system is deliberately coarse: it standardizes the interface, not the performance.
3. Cross-Brand Interchange: What Actually Matches
Because the NMRV interface is a de facto standard — dimensioned drawings circulated for decades and reverse-engineered everywhere — the mechanical interfaces of different brands are highly compatible: footprints, output shaft diameters, keyways, and input flange pilots will usually line up within a fraction of a millimeter. What does not transfer is the performance rating. Two brands’ NMRV 075 units can carry different thermal capacities, service factors, allowable radial loads, and efficiency curves in the same bolt pattern. A substitution is therefore a re-selection exercise, not a label swap.
Before ordering a substitute brand against an installed NMRV unit, verify these five items:
1. Mounting footprint and flange hole spacing
Compare the housing outline, foot bolt pattern, and any output-flange pilot and bolt circle against the installed drawing. Feet and pilots are where near-compatible meets not-compatible.
2. Output shaft diameter, length, and keyway
Match the shaft diameter and key dimensions to your hub or coupling, and confirm the allowable overhung (radial) load for your pulley, sprocket, or gear mounted on it.
3. Input flange interface
Confirm the input flange code — IEC B5 or B14 size, or a NEMA variant — including pilot diameter and bolt pattern, before ordering a motor or adapter. See the input flange section below.
4. Ratio and output speed
The same nominal ratio is not always the same exact ratio across brands. Verify the actual output rpm at your input speed, especially for positioning or synchronized lines.
5. Backlash and precision class
General-industrial and reduced-backlash variants share footprints but not accuracy. If the drive positions rather than just transmits, pin the backlash class in the specification.
The field procedure for the same job — identifying an unlabeled unit, measuring the critical dimensions, and commissioning the replacement — is covered step by step in the worm gear replacement guide.
4. NEMA 56C and IEC B5/B14 Input Flanges
The NMRV input side is natively an IEC motor flange: a large B5 flange or a small face-mounted B14 flange, dimensioned for standard IEC motor frames in the 63–112 range depending on gearbox size. Bolt an IEC motor straight on, and the assembly is a gearmotor.
North American motors use the NEMA C-face system instead, and here lies the classic trap: NEMA 56C is not the same thing as IEC frame 56. The two 56s belong to different dimension systems with different bolt circles, pilots, and shaft diameters, and neither matches the other’s flange. To drive an NMRV from a NEMA 56C or 145TC motor you need one of three things: an input-flange adapter kit (widely available, e.g. 56C-to-B5), a NEMA-flange input variant where the maker offers one, or a shaft-input (NRV-type) unit driven through a coupling or belt.
The full matching workflow — frame-by-frame NEMA versus IEC comparisons, motor power versus frame size, and the gearmotor-versus-separate purchase decision — is laid out in How to Match a Motor to a Worm Gearbox (NEMA and IEC Frame Guide).
5. When a Custom Worm Gear Set Beats a Stock NMRV
The NMRV frame system is deliberately coarse — nine discrete center distances for every duty in the world. That is exactly its strength as a commodity and its weakness as an engineered product. A custom worm gear set is the better route when your requirement falls between frames or outside the standard recipe:
- Non-standard center distance. Your housing fixes the axis spacing — 57 mm, 132 mm, anything not on the R10-style ladder of frames. A custom set is designed to your exact center distance, not the nearest catalog step.
- Material pairings beyond the recipe. Stainless worms for washdown duty, aluminum bronze or plastic wheels for special friction or noise requirements, food-grade lubrication compatibility specified from the start.
- Tighter backlash. Catalog NMRV units ship in general-industrial backlash classes; positioning machinery that reuses the NMRV envelope often needs a ground, adjustable or duo-lead pair instead.
- Rebuilding around an established envelope. When an obsolete or failed unit leaves a bolt pattern worth keeping, the gears can be re-cut to match the surviving housing — you keep the machine, we supply the worm and wheel.
- Documented quality. Inspection reports, material certificates, and measured backlash on the actual pair you receive — specified per order rather than assumed from a catalog class.
That last point is the standing offer behind this page: we supply the gear pair — you integrate it into your housing. Start on the custom worm gear page, or attach your dimensions and target ratio to a quote request and we will respond with a proposed set.
FAQ
Are NMRV gearboxes interchangeable between brands?
Mechanically, largely yes. The NMRV series is a de facto industry standard, so footprints, output shaft sizes, and input flanges are closely — but not always exactly — matched across makers. Performance ratings (torque, thermal capacity, service factors) are not standardized, so run the five interchange checks in this guide and repeat the maker's selection calculation before treating a substitute as equivalent.
What does the number in NMRV 050 mean?
It is the center distance of the worm gear pair in millimeters: in an NMRV 050, the axis of the worm shaft sits 50 mm from the axis of the output (worm wheel) shaft. The same rule decodes every NMRV size from 030 to 150 — a larger number means a proportionally larger housing, output shaft, and torque capacity.
What NMRV sizes exist, and do all makers offer the same range?
The standard range runs 030, 040, 050, 063, 075, 090, 110, 130, and 150. Most manufacturers offer all nine frames; some add smaller (025) or intermediate (105) sizes, and higher-capacity variants exist inside the 063-110 footprints. Always confirm the exact frame list in the specific maker's catalog.
Can I mount a NEMA 56C motor directly on an NMRV gearbox?
Not natively. NMRV inputs are machined for IEC B5 or B14 motor flanges, whose bolt patterns and pilot diameters differ from the NEMA 56C face — NEMA 56C is not the same thing as IEC frame 56. Use an input-flange adapter kit, a NEMA-flange input variant where a maker offers one, or a shaft-input unit with a coupling; our motor matching guide covers the options.
Can you manufacture a custom equivalent to an NMRV worm gearbox?
We manufacture custom worm gear sets — the worm and wheel pair — ground and inspected to your drawing. If you are rebuilding gearboxes around an NMRV envelope, need a non-standard center distance or material pairing, or want tighter backlash than catalog units provide, send the geometry through our quote form and we will propose a custom equivalent.
Need a Custom Equivalent to an NMRV Unit?
Send the frame number, ratio, and target performance of the NMRV unit you are working around — or the measured center distance and shaft geometry of a failed set — and our engineers will propose a custom worm gear pair for your housing, with a quote returned within 24 hours.