Need custom worm gears? Contact us — WhatsApp +86 138 1403 4409 · worm@wormgearmfg.com
ISO Certified
DIN 4-5 Precision Grade
Custom Manufacturing
Service

Reverse Engineering

Worn or broken worm gear? No drawing? We reverse-engineer from your sample — full CAD model, improved design, and replacement production.

Our 7-Step Reverse Engineering Process

1

Sample Receipt & Assessment

You send us the worn or broken gear (or we visit your facility). We photograph, measure, and document the sample condition. We determine what caused the failure.

2

3D Scanning & CMM Measurement

We digitize the gear using coordinate measuring machines (CMM) and optical scanners. Profile deviation, lead angle, pitch, and all critical dimensions are captured to ±1-2 μm accuracy.

3

Gear Tooth Analysis

The tooth profile is analyzed on our gear measuring center. We determine the original cutting method (hobbed or ground), module, pressure angle, and any crowning or tip relief.

4

Material Identification

Spectrometry identifies the exact alloy composition. Hardness testing reveals heat treatment condition. Metallography shows grain structure, case depth, and any material defects.

5

CAD Model & Drawing Creation

We reconstruct a 3D CAD model and generate a production drawing with GD&T tolerances. The drawing includes all dimensions, materials, heat treatment, and surface finish specifications.

6

Design Improvement (Optional)

We analyze why the original gear failed and propose design improvements: better material, optimized tooth profile, revised heat treatment, or surface coating. This extends service life.

7

Prototype & Validation

A prototype gear set is manufactured and tested for fit, function, and noise. You validate it in your application before we proceed to production.

Common Failure Modes & Improvements

Failure SymptomRoot CauseOur Improvement
Pitting on wheel teethContact fatigue from overload or inadequate lubrication film thicknessIncrease module, upgrade to aluminum bronze, or improve oil viscosity
Scoring/scuffing on worm threadsMetal-to-metal contact from insufficient lubrication or excessive load/speedAdd anti-scuff coating (TiN/DLC), increase oil viscosity, or reduce load
Broken worm shaftFatigue from inadequate core strength or stress concentration at keyway/thread transitionUpgrade material (42CrMo4 to 4340), add fillet radius, improve heat treatment
Excessive backlash growthAbrasive wear from contaminated oil or mismatched hardness between worm and wheelHarden worm to 60+ HRC, add sealed housing with breathers, use cleaner lubricant
Corrosion damageWater ingress or chemically aggressive environment attacking bronze wheelSwitch to aluminum bronze or coated steel, improve seals, use rust-inhibited oil

Capabilities & Deliverables

1
Minimum sample condition: Even heavily worn gears with 30%+ material loss can be reverse-engineered
2
Measurement accuracy: CMM ±1.5 μm, Gear measuring center ±0.5 μm, Optical scan ±5 μm
3
Material analysis: OES spectrometry, hardness (HRC/HV/HB), metallographic sectioning
4
Typical turnaround: CAD model + drawing: 3-5 days | Prototype: 7-10 days | Production: 10-15 days
5
Deliverables: 3D STEP/IGES file, 2D PDF drawing, material report, improvement recommendation

Send Us Your Sample — We Will Rebuild It Better

Ship your worn gear to us for analysis. Within 3-5 days you will receive a CAD model, failure analysis, and improvement recommendations — all credited toward your production order.

Reverse Engineering FAQs

Can you reverse-engineer a gear if I only have a broken piece?

Yes, in most cases. Even a single tooth fragment contains enough geometric information to reconstruct the full profile. We use gear geometry principles and statistical averaging from remaining teeth. For best results, send as much of the original gear as possible.

Do I need to send you the mating gear too?

Ideally yes. Having both the worm and wheel allows us to verify the center distance, backlash, and contact pattern. If only one component is available, we can still reverse-engineer it, but the mating component will be designed to match based on calculated conjugate geometry.

How much does reverse engineering cost?

Reverse engineering typically costs $300-800 depending on complexity and sample condition. This includes 3D scanning, CMM measurement, material analysis, and CAD model creation. The fee is credited toward your production order. Prototype and production are quoted separately.

Will the replacement gear last longer than the original?

Often yes. Because we analyze why the original failed, we can address the root cause. Common improvements include: upgrading from sand-cast to centrifugal-cast bronze, increasing case depth on the worm, adding surface coatings, or optimizing the tooth profile for better load distribution. Many customers report 30-100% longer service life.

Can you reverse-engineer gears from competitors or obsolete equipment?

Yes. We regularly reverse-engineer gears for which drawings are lost, manufacturers are out of business, or spare parts are no longer available. We provide full documentation so you own the design and are never dependent on a single source again.